|
Courtesy of
HandiCraftShop.com
* Cut the pattern paper. (PATTERN 2 pages)
* Place the pattern on the back (inside) of fabric.
* Draw along the pattern on the fabric.
* Cut the fabric along the pattern drawn.
- Please see the picture, showing the drawings completed.
** Check and confirm the fabric cut along the pattern.
1. Body (bottom side) pink - 1 piece.
2. Body (right and left) pink - 2 piece.
3. Nose (white) - 1piece
4. Face (right and left) pink - 2 pieces.
5. Face (center) pink - 1piece.
6. Tail (Inside: white, Outside: pink) - 2pieces.
7. Ear-inside (right and left) white -2pieces.
8. Ear-outside (right and left) pink -2pieces.
*** Notice. Sewing must be done 3-4mm from the edge of the fabric.
Materials:
1. Two kinds of Cottony Fabric
1-1. Pink color desirable length. 20 cm x 60 cm
1-2. White color desirable length 10cm x 10 cm
2. Three (3) kinds of thread.
2-1 Thin white thread - to sew 2 panels together.
2-2 Thick white thread- to attach the head to the body.
2-3 Thick dark pink thread – to stitch the nose and the mouth.
3. Two eyes (made of plastic materials)
4. Acetate cotton boll (to fill the body)
5. Pattern.
Suggested Tools:
1. Two kinds of needles.
* Long needle (To attach the head to the body and to stitch the nose and the mouth)
* Fine needle (To do other sewing job, except for the above)
2. A pair of scissors- to cut pattern and fabric
3. Awl- to make eyeholes
4. Pen- to draw patterns on the fabric.
Handy To Have:
1. Make 2 ears.
The inside of ear is white one and the outside of ear is pink.
Do the finish-up running stitching first on 3 corners.(marked with black dots).
Put 2 pieces of ear pattern fabric inside out and then backstitch.
* Right: Showing the completed ear by turning inside out
 
2. Make tail.
Put 2 pieces of tail pattern fabric inside out and then backstitch. Do the finish-up running stitching first on 3 corners.(marked with black dots)
Dart stitching on the center of tail. Below Showing the completed tail by turning inside out.
 
3. Make upper body.
a. Put 2 pieces of upper body(right side panel and left) pattern and then backstitch.
Do the finish-up running stitching first on 4 corners.(marked with black dots)
b. Insert tail made in #2 as shown in the picture (1) and then backstitch.
 
 
4. Make nose and front of the head.
Dart stitching on white nose of pattern fabric. (Please refer to the picture)
Sew along the brown dotted line.
 
5. Make side of the head.
Dart stitching on the side of the head.(Right and left, 2 pieces) (Marked with green dots)
  
6. Attaching the nose to the center of head. (Please refer to the arrows in the picture.)
  
7. Attaching the bottom of the body to the upper body.
Do the finish-up running stitching first on 4 points.(Marked with black dots.)
  
Showing the completed body after turning inside out.
8. Make head.
a. Attaching the right side of head to the left side of head.
- Sew along the black dotted line.
Attaching the right side and left side of head to the front of head.(#8a + #6)
Do the finish-up running stitching first on 6 points to firmly fix, and backstitch.
(Do not backstitch two blue lines. This area is to be stitched with ear.) (You will match color, and numbery the dots.) Please refer to the picture below.
  
9. Insert ear made in #8 as shown in the picture and then backstitch.
(The ear position is #8 along the blue line, where you didn¡¯t do backstitch.)
  
Showing the completed ear after inserting in the head and turning inside out.
10. Attach eyes.
- Make holes on both upper side of nose(white area) and insert plastic eyes already prepared.
11. After the sewing of the body and the head is completed, turn inside out, and then stuff the cotton into the body and head as shown in the picture.
12. Attaching the head to the body.
(Sewing method: Stitching to seal by skipping over one stitch)
- Tools and supplies to be prepared: Thick long needle and thick thread.
- As in the picture, attach the neck to the body by sewing around them.
- Tie a knot on the front part of the neck to complete, and pull the needle through the neck to the back and cut the thread, so that the thread can¡¯t be seen.
13. Make face.
- Sewing Nose and Mouth.
Put several strips of dark orange thread through the thick needle, do one stitch, from the left-top of white are to the right-top, and then put needle through the middle part
as in the picture, white area.
   
Finish up in the middle part, by doing one stitch down to the bottom of the nose(white), and put the needle through the back of the neck and cut the thread, so that the thread can¡¯t be seen
- Make solid-look face.
The face looks a lot nicer if the eyes, nose and mouth are dented on the face. - As in the picture, put the needle into the neck and pull it through where the upper part of the eyes are.
Then put the needle back by doing a very short running stitch and pull thread, so the thread can¡¯t be seen, and pull the needle again through the neck.
14. Completed. Cutesy Rabbit.
Add
Suggested Products to Your Shopping Cart:
Our editors have selected various products from our shopping cart
for you to use in making this project. You can add these products
directly to your shopping cart by clicking on the " Add to
Cart" button below. If you wish, you can change the quantity of
any product by changing the number in the "QTY" box next
to the product, or remove an item from the materials list altogether
by leaving the "QTY" box blank. Once you click on the
"Add to Cart" button, you can still alter your selections.
To return to this page from the shopping cart, please use your
browser's "Back" button.Click
hereto learn more about using our shopping cart.
Every effort has been
made to ensure the accuracy and completeness of these instructions.
We cannot be responsible, however, for variances in individual
techniques, human errors, or typographical mistakes.
|
